Honeywell Fire Alarm System

We are ranked amongst the renowned organizations that are engaged in providing the best quality range of Addressable Fire Alarm Control Panel.

NOTIFIER’s intelligent addressable isolator module, the ISO-X is used with Fire Alarm Control Panels to protect the system against wire-to-wire short circuits on the Signaling Line Circuit loops. The ISO-6 is a six fault isolator module providing isolation on six equivalent circuits.

Features & Benefits:

• Enables part of the communications loop to operate when a short circuit occurs
• Automatically resets on correction of short
• ISO-X
  • SEMS screws with clamping plates for ease of wiring
• ISO-6
  • Removable 12 to 18 AWG plug-in terminal blocks
  • Six individual, Class B isolator circuits
  • Specifications
    • Normal Operating Voltage: 15-32 VDC
    • Stand-By Current: 450μA (not isolating) per circuit
    • Maximum Current Draw: 17mA (device in isolation)
    • Temperature Range: 32°F to 120°F (0°C to 49°C)

NOTIFIER''s offers a variety of intelligent monitor modules for diverse applications. Monitor modules supervise a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two-wire smoke detectors. Monitor modules model numbers include the FMM-1, FMM-101, FZM-1 and FDM-1.
Features & Benefits:  

Built-in type identification automatically identifies this device as a monitor module to the control panel

SEMS screws with clamping plates for ease of wiring

Direct-dial entry of address: 01 – 159

LED indication for normal or off normal indication

FMM-1 Monitor Module

Class A supervised wiring to the monitored device

FMM-101 Mini Monitor Module

Class B supervised wiring to the monitored device

Smaller size fits inside devices or junction boxes

FZM-1 Zone Interface Monitor Module

Transmits the status of one zone of 2-wire detectors to the fire alarm control panel

Status conditions are reported as normal, open, or alarm

FDM-1 Dual Monitor Module

Monitors two separate Class B circuits

 
SD355(A)/SD355T(A) Smoke Detectors
Fire-Lite's SD355 and SD355T addressable, low-profile, plug-in photoelectric detectors use a state of the art photoelectric sensing chamber to provide open area protection and are used exclusively with the MS-9050UD, MS-9200UDLS, and MS-9600(UD)LS Addressable Fire Alarm Control Panels. The SD355T adds thermal sensors that will alarm at a fixed temperature of 135F (57C

Photoelectric Sensor

Notifier FSP-851AUS Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector's address to be set with decade address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. The FSP-851 photoelectric detector's unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. FSP-851 detectors are compatible with all Notifier intelligent Fire Alarm Control Panels (FACP).

 

Features:

Sleek, low-profile design.

Addressable-analog communication.

Stable communication technique with noise immunity.

Low standby current.

Two-wire SLC connection.

Compatible with FlashScan® and CLIP protocol systems.

Rotary, decimal addressing (1-99 on CLIP systems, 1-159 on FlashScan systems).

Dual LED design provides 360° viewing angle.

Visible bi-color LEDs blink green every time the detector is addressed, and illuminate steady red on alarm (FlashScan systems only).

Remote test feature from the panel.

Walk test with address display (an address on 121 will blink the detector LED: 12-[pause]-1(FlashScan systems only).

Built-in functional test switch activated by external magnet.

Built-in tamper-resistant feature.

The MMF-300 Monitor Module is intended for use in addressable, two-wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides either a 2-wire or 4-wire fault tolerant Initiating Device Circuit (IDC) for normally open contact fire alarm or supervisory devices. The module has a panel controlled LED indicator. The MMF-300 can be used to replace an M300 module in existing systems.

Product Specification Product DescriptionThe CMF-300(A) Addressable Control Module providesFire. Lite intelligent control panels a circuit for NotificationAppliances (horns, strobes, etc.). Addressability allows theCMF-300(A) to be activated through panel programming, on aselect (zone or area of coverage) basis.

LiteSpeed™ is a communication protocol developed byFire. Lite Engineering that greatly enhances the speed of com-munication between analog intelligent devices. Intelligentdevices communicate in a grouped fashion. If one of thedevices within the group has new information, the panel CPUstops the group poll and concentrates on single points. Thenet effect is response speed greater than five times that ofother designs

Features:

• Built-in   type   identification   automatically  identifies   thesedevices to the control panel
• Internal  circuitry  powered  directly  by  two-wire  SLC  loop
• The   CMF-300(A)   module   requires   power   (for   horns,strobes, etc.)
• Integral  LED  “blinks”  green  each  time  a  communication  isreceived  from  the  control  panel  and  turns  on  steady  redwhen activated
• High noise immunity (EMF/RFI)
• The  CMF-300(A)    may  be  used  to  switch  24-volt  NACpower
•  Wide viewing angle of LED
• SEMS screws with clamping plates for wiring ease
• Direct-dial  entry  of  address:  01-159  for  MS-9600  seriespanels, 01-99 on MS-9200UDLS and MS-9050UD

Applications

• The  CMF-300(A)  is  used  to  switch  24  VDC  audible/visualpower

Construction

• The face plate is made of off-white heat-resistant plastic
• Controls include two rotary switches for direct-dial entry ofaddress setting
• The CMF-300(A) is configured for a single Class B (Style Y)or Class A (Style Z) Notification Appliance Circuit

Operation:Each  CMF-300(A)    uses  one  of  the  module  addresses  on  aSLC  loop.  It  responds  to  regular  polls  from  the  control  paneland  reports  its  type  and  status,  including  the  open/normal/short  status  of  its  Notification  Appliance  Circuit  (NAC).  The LED blinks with each poll received. On command, it activatesits internal relay. The CMF-300(A)  supervises Class B (StyleY) or Class A (Style Z) notification or control circuits.

The FAPT-851AUS Acclimate™ detector uses a combination of photoelectric and thermal sensing technologies to increase immunity to false alarms. Unlike traditional intelligent detectors, the Acclimate™ detector has a microprocessor in the detector head that processes alarm data. As a result, the Acclimate™ detector adjusts its sensitivity automatically, without operator intervention or control panel programming.

Areas where the Acclimate™ detector is especially useful include office complexes, schools, college campuses, manufacturing and industrial facilities, and anywhere else the use of a particular area may change.

 

Features:

• • Automatically adjusts sensitivity levels without operator intervention or programming.
  • Addressing by rotary decade switch.
  • Dual bi-color LED design provides 360° viewing angle.
  • Built-in tamper-resistant feature.
  • Capable of heat-only alarm mode, enabled by a special command from the FACP.